Powder pelletizing machine

No water/binder
Hydraulic/physical press
Low water/power/space consumption
High strength/density
Powder pelletizing machine
Powder pelletizing machine operating principle:
The machine adopts the couple roller. Between the rollers, there is certain gap. Using double output shaft reduction machine, makes the couple roller in phase and run face to face. One group of roller axle seat is fixed and another group of roller axle seat is slipped. With the support of the pressure of hydraulic cylinder, they are close to each other and the hydraulic system can has the action of compensation and protection. In the surface of the roller, the hole (arc trough) of many shapes and same size are arrayed. According to the different compression rate of the materials, choose the trough of one roller aiming at the trough of another roller, or peak to trough. Two rollers is arranged in horizon. The powder material on itself weight is compulsorily feed into the gap between two rollers over the rollers continuously and equally. When the material enters into the gripping area, it is gripped by the roller. With the continuous turning or the roller, the occupied space of the material is less and less and gradually compressed and reaches the max value of the formation pressure. Then, the pressure gradually reduces. The flakes due to its elasticity and self weight breaks off the arc trough, sieves.
Powder
p
elletizing machine t
echnical parameter:
a).roller diameter: 504 available width: 300mm
b).roller turning speed:14-20rpm.
c).compulsory feeder: 11kw motor frequency conversion speed adjusting, ration conveyor, 2.2kw frequency conversion speed adjusting
d).accumulator pre-pressurization: 6-10Mpa
e).allowable max. formation pressure rate: 55kn/cm
f). dimension of spherulite: 41×28×22
g).power of compacter principal machine: 75kw
h).installed capacity: about 88kw
i).dimension (L×W×H) : 3650×2250×2500
j).weight: about 18t
k).output:6-8t/h
Powder
p
elletizing machine

components:
1) Ration feeding device: Composed of raw material silo and star type charger with fixed amount transportation, 2.2/1.5kw power, frequency conversion speed adjustment.
2) Compulsory feeding machine: Composed of charger with 11kw frequency conversion speed adjusting motor, taper helix, agitator knife, taper charger with observation window and feeding bucket. This is to further finish degasification and pre-compress the powder.
3) Compacter: Composed of fixed axle seat and slipped axle seat, two alloy steel rollers, two hydraulic cylinder and pump, double output reduction machine, Type GIICL drum jugged shaft coupling and 75kw electromotor set.
4) Electrical control cabinet: Composed of electrical control box, frequency conversion speed adjusting controller, ammeter, voltmeter, instruction light, button, voltage conversion switch, etc.
5) Vibrating screen: (one set) the grinded material from the grinding and pelletizer is screened into the grain by this machine and recycled powder. SFJH100×2C
6) Bucket hoisting machine HL200. Equipped based on the request.
Powder
p
elletizing machine
application:
1.fertilizer:

Potassium Sulfate(SOP), potassium chloride, Russia red potassium, potassium nitrate, ammonium chloride, Ammonium Phosphate Monobasic, Diammonium phosphate(DAP), NPK compound fertilizer, import Russia Potassium Sulfate(SOP), ground phosphorite, NH4SO4, concentrated superphosphate, humic acid etc.
2.power material
zinc oxide, lead oxide, calcium chloride, calcium phosphate, High test bleaching powder, cryolite, chemical inhibitor, silica, Isophthalodinitrile etc.
3.chemical raw material, fine chemical material
4.desulfurization gypsum
5.coal power
Note:
It takes desulfurization gypsum for example, all above parameter will be different in accordance with the material to be pelletized.